What a DJI Fly waypoint mission does when the signal drops or the battery runs low

The drone went home mid-mission with Continue selected, or Continue wasn't in the list at all. The documented causes are the mission's On Signal Lost setting, the EU limit on it and low battery RTH. DJI's manuals cover those; the rest is forum reports.

By Sander Helgesen · Last checked

In short

  • In a waypoint mission the drone follows the route's On Signal Lost setting: RTH, Hover, Land or Continue. The Signal Lost setting under Safety is a different one.
  • Continue can't be set in the EU, say the manuals for the Mini 4 Pro, Mini 5 Pro, Air 3, Air 3S and Mavic 4 Pro. The Mavic 3 Pro manual lists Continue with no such note.
  • Once a signal-loss RTH has started, the drone stays in RTH when the signal returns. You can take over with the RTH button or in DJI Fly, but the mission doesn't rejoin by itself.
  • Low battery is a separate trigger. When there is only enough left to fly home, DJI Fly shows a prompt, and if nobody answers before the countdown ends the drone goes home.

On Signal Lost: four choices, one per mission

On Signal Lost is a mission setting, on the same page as Global Speed and End of Flight, and it applies to the whole route. The Mini 4 Pro and Air 3 manuals give it one line: "When the remote controller signal is lost during flight, the aircraft will perform the action set in On Signal Lost." The three newest manuals mention the setting only in their EU note.

The KMZ column is from DJI's WPML reference, which lists only enterprise drones for these elements. DJI Fly's own files carry them too, and we have seen goBack and hover there. The last column is our suggestion, not DJI's.

The four On Signal Lost choices, what the drone does and how a KMZ stores them

  • RTH

    What the drone does
    Leaves the mission and flies to the Home Point under your RTH settings
    In the KMZ
    exitOnRCLost executeLostAction, executeRCLostAction goBack
    Our suggestion
    Most jobs, with an RTH altitude that clears the way home
  • Hover

    What the drone does
    Stops where the link dropped and holds position
    In the KMZ
    exitOnRCLost executeLostAction, executeRCLostAction hover
    Our suggestion
    The way home isn't clear and you can get closer to bring the link back. If the link stays down, expect low battery RTH to fly that same way home
  • Land

    What the drone does
    Lands where it is
    In the KMZ
    exitOnRCLost executeLostAction, executeRCLostAction landing
    Our suggestion
    All the ground under the route is open and you can reach it
  • Continue

    What the drone does
    Keeps flying the route with no link. With obstacle avoidance on, it brakes and hovers at an obstacle it detects
    In the KMZ
    exitOnRCLost goContinue
    Our suggestion
    Where it is offered, on a route you keep in sight. You can't steer or stop it until the link returns

Why it went home with Continue selected

There are two signal settings. On Signal Lost belongs to the mission and can offer Continue. Signal Lost under Settings > Safety offers RTH, Hover and Descend or Landing, depending on the manual, and no Continue. During a waypoint mission, the manuals point to On Signal Lost. If DJI Fly showed a return prompt, rule out low battery first: low battery RTH can send the drone home whatever On Signal Lost says (below). Beyond that, forum threads offer three explanations, one thread each, none confirmed:

  • Possibly the EU limit. A Mini 4 Pro pilot on the Litchi forum switched the controller off to test an Onboard mission, and the drone went home however the settings were changed. Another member pointed to the EU limit, in case the pilot was in Europe.
  • Possibly Litchi flying the mission, not the drone. A Mini 4 Pro pilot in Brazil lost the link and the mission stopped. The answer on the forum: in Litchi Pilot, Flight engine has to be Onboard for a mission to continue after signal loss. The pilot replied that this may be the problem.
  • Possibly a return prompt running out. A Mini 4 Pro pilot in the US, on Continue, reported what they took for blips of signal after a loss, got a prompt to return, and cancelled it on four long flights. When they left it alone, the drone came home, and they believe the prompt was the reason. They also believed Safety was set to RTH. The thread doesn't say which prompt it was. The low battery prompt works this way, but nothing confirms it was that one.

Continue in the EU, drone by drone

The Mini 4 Pro manual's wording: "When using Waypoint Flight in the EU, the behavior of the aircraft when the remote controller signal is lost cannot be set to Continue." The newer manuals say the same in fewer words.

DJI writes "in the EU" and names no countries. Norway is outside the EU but follows its drone rules, and the manuals don't say how DJI Fly treats it. Members of the Litchi thread disagree on the mechanism: some describe CE firmware or an EU drone, another says the drones are the same everywhere and switch behaviour by location. The Mavic 3 Pro's missing note doesn't prove Continue works there either. The list in your own app decides, and we have not tested what DJI Fly does with a goContinue file in the EU.

The table shows the English manuals linked from DJI's download pages, read on 2026-11-04, with the version printed in each:

What each DJI manual says about Continue in the EU

  • Mini 4 Pro

    Manual
    v1.4, June 2024
    On Signal Lost in the EU
    Can't be set to Continue
  • Mini 5 Pro

    Manual
    v1.0, September 2025
    On Signal Lost in the EU
    Can't be set to Continue
  • Air 3

    Manual
    v1.6, June 2024
    On Signal Lost in the EU
    Can't be set to Continue
  • Air 3S

    Manual
    v1.0, April 2026
    On Signal Lost in the EU
    Can't be set to Continue
  • Mavic 3 Pro

    Manual
    v1.4, August 2024
    On Signal Lost in the EU
    Lists Continue, no EU note
  • Mavic 4 Pro

    Manual
    v1.2, September 2025
    On Signal Lost in the EU
    Can't be set to Continue

After the link drops

  • How fast. The Mini 5 Pro, Air 3 and Mavic 3 Pro manuals say Failsafe RTH starts after more than six seconds without signal. The Mini 4 Pro's June 2024 file said the same; its July 2026 re-issue, under the same version label, gives no number. The Air 3S and Mavic 4 Pro manuals give none either, and none gives a separate delay for waypoint flights.
  • It doesn't rejoin the mission. "The aircraft will remain in RTH even if the remote controller signal is restored." Once the link is good you can exit RTH with the RTH button or in DJI Fly and fly the drone yourself. To fly the rest of the route, start again after landing (steps below).
  • Where it goes. The last recorded Home Point, not where you are standing. You can update it in Settings > Safety while you have the link, and with an RC 2 the Mini 5 Pro and Mavic 4 Pro offer Dynamic Home Point, where the drone returns near the Home Point, exits RTH and hovers for you to take over. A moved Home Point moves the line home, so a height worked out for the takeoff may no longer clear it.
  • How it flies home, in the Mini 4 Pro, Mini 5 Pro, Air 3, Air 3S and Mavic 4 Pro manuals. More than 50 m out on Preset, when the vision systems work, it flies to an open area, climbs to the RTH altitude if it is below it, and comes home by the best path it can plan. When they don't work, it climbs and flies home in a straight line. Between 5 and 50 m it comes home at its current altitude, with no climb. Under 5 m it lands at once. On Optimal, when the vision systems work, it plans its own path and height regardless of the RTH Altitude setting.
  • When vision doesn't work, in poor light or unsuitable surroundings. After a signal loss more than 50 m out the drone flies 50 m back along its route, then goes on to Preset RTH. Without vision it can't sense obstacles on that flight, apart from the LiDAR below.
  • Exceptions. The Mini 5 Pro, Air 3S and Mavic 4 Pro have a forward LiDAR. Their RTH table says it can climb over an obstacle in poor light, but their row for lost signal says the drone brakes and hovers at an obstacle, and their 5-50 m row says it brakes and hovers for you to take control. With no link, expect that hover to last until low battery. Without vision the Mavic 3 Pro uses Straight Line RTH: more than 50 m out, a first climb to 20 m, then on to the RTH altitude.

Low battery overrides the mission

The manuals list three triggers for RTH: you, low battery and lost signal. DJI Fly shows a warning when the battery is low and "only sufficient to fly to the Home Point". If you confirm, or "do not take action before the countdown ends", the drone starts low battery RTH. The Mavic 3 Pro manual gives the countdown as 10 seconds and says the warning comes only once per flight.

The sum counts the way back from where the drone is now, using its position, the environment and flight speed. So a long one-way route gets the prompt far earlier than a loop of the same length. One pilot had a point-to-point route turned round this way.

If you cancel and keep flying, DJI warns that the battery may not have enough power to land, which can mean a crash or a lost drone. The drone lands by itself once the battery can only just cover the descent, and that landing can't be cancelled. With the link up you can still steer it sideways, so use that time to reach a clear spot.

Set a mission up for a lost link

On the ground, before you tap GO.

  1. Read On Signal Lost

    Open the mission and go to the route settings page before GO. In a planner's KMZ the value is in wpmz/template.kml and wpmz/waylines.wpml: exitOnRCLost and executeRCLostAction. Change a planner's file in the planner; the KMZ guide says not to edit it on the controller.

  2. Choose what the drone should do

    Use the table above. Without a strong reason for another choice, use RTH.

  3. Set an RTH altitude that clears the way home

    A DJI Fly KMZ doesn't carry this: set it in DJI Fly under Settings > Safety, even when a planner gives you the number. Find the highest point on the straight line home from anywhere on the route, whether terrain, a tree, a mast or a building, in metres above the takeoff, and add a margin. RTH altitude counts from the takeoff, so a ridge 60 m above it needs more than 60 m. In a canyon the line home can cross the rim. Inside 50 m the drone stays at waypoint height, so that line has to be clear as well. Max Altitude has to be at least as high; the limits guide covers both. If the height you need is above what the app allows, move the takeoff or split the route.

  4. Check zones on the way home

    Near a GEO zone that height doesn't settle it: the drone can leave the line to go round the zone, and near an Altitude Zone it can drop below your RTH altitude. In very complex surroundings it can exit RTH altogether. Check the way home on a zone map.

  5. Choose Preset when you rely on that height

    On Optimal the drone ignores RTH Altitude while its vision systems work. DJI's own advice is to set Advanced RTH to Preset if there are power lines or towers it can't bypass on the way home, with the RTH altitude above all obstacles. It can't avoid small or fine objects such as branches and power lines.

  6. Budget for the way back

    Low battery RTH counts the way home from wherever the drone is, so finish well before it. Split a long job into flights from the same takeoff. On a one-way route, you can update the Home Point as you follow the drone; know what cancelling the return risks.

It came home early: finish the job

A mission doesn't resume by itself, so you fly the rest as a new start.

  1. Fix the cause

    After a lost link, plan again with the takeoff and your own position closer to the far end, or split the route. After a low battery return, cut the route into shorter flights.

  2. Take off from the right spot

    The same file needs the same takeoff, because every waypoint height counts from it. From another spot it flies at other heights. A new plan: take off where that plan says.

  3. Find where it stopped

    The last photo on the card shows how far it got. On a mapping grid, go back to the start of the interrupted line, so the overlap holds.

  4. Fly the rest

    With a planner's KMZ, plan the remaining part again and install the new file, so a planner that checks covers the new first leg. For a mission built in DJI Fly, set Start Point on the route settings page before GO: "the flight route will be started from this waypoint to the subsequent waypoints." The Mini 4 Pro, Air 3 and Mavic 3 Pro manuals describe it. We have not tested it on a planner's KMZ, and nothing has checked the leg from the takeoff to that waypoint.

If you fly with Litchi

One forum member says Litchi Hub has no signal-lost setting: you set On Signal Lost on the controller when you fly the mission in DJI Fly. Another says that in Litchi Pilot, only Flight engine Onboard can keep flying after signal loss. Both are forum answers, not Litchi's documentation.

What the manuals leave open

  • How long Hover lasts with no link. Expect the battery limits above to end it.
  • What a low battery prompt does on Continue with no link. With no link nobody can tap it, so expect the drone to go home when the countdown ends.
  • Which action runs when a Continue mission ends with no link. DJI's WPML reference says "the runaway action will be executed first" and doesn't say how that maps to DJI Fly's settings. Our suggestion, not DJI's: if you use Continue, set End of Flight and Signal Lost under Safety to RTH, and accept that the drone may come home early. The manuals don't say how the two interact, and the US pilot above believed Safety was on RTH when the drone came home.

Where Skyplanr fits in

Skyplanr's plans use RTH on a lost signal, and its files never contain Continue. From every waypoint more than 50 m out, the checks test the straight line home to the takeoff at the plan's RTH height, the path Preset RTH flies without vision, against terrain and the roofs and obstacles in its data. They also test the low direct return from closer than that. They warn when there is no obstacle data, and wires may be missing. On a one-way route they warn from which waypoint the low-battery return can turn the drone round. Those checks assume you set Advanced RTH to Preset and that altitude in DJI Fly, because the file can't. The checklist gives you the RTH altitude and Max Altitude to set. 3 AI plans a month are free; see pricing.

See the technology

Questions

What happens if a DJI Fly waypoint mission loses signal?

The drone does what the mission's On Signal Lost setting says: RTH, Hover, Land or Continue. The Mini 5 Pro, Air 3 and Mavic 3 Pro manuals say Failsafe RTH starts after more than six seconds, with no separate figure for waypoint flights. Once RTH has started, the drone stays in RTH even if the signal returns, and you can exit it and fly yourself once the link is good.

Why can't I select Continue for On Signal Lost in DJI Fly?

The manuals for the Mini 4 Pro, Mini 5 Pro, Air 3, Air 3S and Mavic 4 Pro say On Signal Lost can't be set to Continue in the EU. The Mavic 3 Pro manual has no such note. The list in your own app decides.

Does a DJI Fly waypoint mission resume after RTH?

No. Land, swap the battery if needed, and fly the rest as a new start. The same file needs the same takeoff. With a planner's KMZ, plan the remaining part again, so a planner that checks covers the new first leg. For a mission built in DJI Fly, Start Point on the route settings page starts from the waypoint you need; nothing has checked the leg from the takeoff to it.

What does low battery do during a waypoint mission?

When there is only enough left to fly home, DJI Fly shows a warning. If you confirm or don't act before the countdown ends, the drone starts low battery RTH. If you cancel, DJI warns it may not have enough power to land, and it lands by itself once the battery can only just cover the descent.

What RTH altitude do I need for a waypoint mission?

Higher than the highest point on the straight line home from anywhere on the route, in metres above the takeoff, plus a margin. Use Preset, since Optimal ignores RTH Altitude while the vision systems work. Max Altitude has to be at least as high.

Sources

Skyplanr is not affiliated with the third-party guides linked here.

  1. DJI Mini 4 Pro User Manual v1.4 (June 2024): Waypoint Flight, Return to Home (terra-1-g.djicdn.com)
  2. DJI Mini 5 Pro User Manual v1.0 (September 2025): Waypoint Flight, Return to Home (terra-1-g.djicdn.com)
  3. DJI Air 3 User Manual v1.6 (June 2024): Waypoint Flight, Return to Home (dl.djicdn.com)
  4. DJI Air 3S User Manual v1.0 (April 2026): Waypoint Flight, Return to Home (dl.djicdn.com)
  5. DJI Mavic 3 Pro User Manual v1.4 (August 2024): Waypoint Flight, Low Battery RTH (dl.djicdn.com)
  6. DJI Mavic 4 Pro User Manual v1.2 (September 2025): Waypoint Flight, Return to Home (terra-1-g.djicdn.com)
  7. DJI Developer: DJI WPML template.kml reference (finishAction, exitOnRCLost, executeRCLostAction) (developer.dji.com)
  8. Litchi forum: Mini 4 Pro goes home on signal lost whatever the settings (June 2025) (forum.flylitchi.com)
  9. Litchi forum: Flight engine has to be Onboard to continue after signal loss (November 2025) (forum.flylitchi.com)
  10. Litchi forum: Mini 4 Pro on Continue, the two signal settings and the return prompt (January 2025) (forum.flylitchi.com)

This guide describes how DJI Fly behaved when it was last checked; DJI can change the app at any time. It is advice, not a permission: you are the pilot in command, and the site, the geo-zones and the rules are yours to check before takeoff.

Let Skyplanr write the file.

Describe the job, and Skyplanr plans the waypoint mission, checks it and gives you the KMZ for DJI Fly.

Plan a mission free