Drone roof inspection: what to photograph, how close to fly and which drone to use
A drone roof inspection is a set of sharp, overlapping photos that let you find a defect and show where it is, without a ladder. What matters is how close you fly, the order of the shots, and stopping for each photo.
By Sander Helgesen · Last checked
In short
- Shoot in this order: a few overview photos so every detail can be placed, a straight-down grid over the roof, angled photos along each eave, then close stops at chimneys, skylights and flashing.
- For defects such as cracked tiles and flashing, aim for 1 cm/px or finer. With an Air 3S in the 12 MP mode that is about 28 m from the roof.
- Stop and hover at each photo, with overlap of about 70%. Motion blur hides exactly the small things you came to see.
- Fly in even light, ideally overcast, and hold off in strong wind. Low sun throws long shadows, and it glares on wet roofs and solar panels.
- A drone shows the surface. It does not replace someone checking inside the attic, testing moisture or signing a condition report.
How close do you need to fly?
The pixel size on the roof (GSD) decides what you can see, and it depends on the distance. The numbers below are for an Air 3S in the 12 MP mode. The LoD vs GSD guide has more on what a pixel size can and cannot promise.
Keep some distance even when the numbers allow less. Skyplanr never plans closer than 5 m to what its data shows. If you need finer detail than that allows, use the telephoto lens rather than moving in.
What the photos must show, and how close to the roof an Air 3S has to be in the 12 MP mode. The telephoto lens gives the same detail from further away.
Overview
- GSD
- 2-5 cm/px
- Distance
- 57-142 m
General condition, gutters
- GSD
- 1-2 cm/px
- Distance
- 28-57 m
Defects: cracked tiles, flashing
- GSD
- 1 cm/px
- Distance
- 28 m
Fine detail: fasteners, sealant
- GSD
- 0.3-0.5 cm/px
- Distance
- 9-14 m
How to inspect a roof with a drone
One house or small building with a DJI Fly drone, from the overview to the close detail.
Take the overview first
Two to four angled photos from about 30 to 60 m away, around the building, gimbal at -30° to -45°. Later, these tell you which part of the roof each close-up shows.
Fly a straight-down grid
Lines over the whole roof plus a couple of metres beyond the edge, camera at -90°, about 70% overlap both ways. This shows the covering, valleys and gutters on flat and pitched roofs alike.
Shoot each pitched plane at an angle
A straight-down photo sees a steep roof at a slant. Fly along each eave with the camera square to the roof plane: -45° to -60° on most pitched roofs. Take a photo about every 40% of the frame width.
Stop at the details
Chimneys, skylights, flashing, vents and antennas get their own stops. Fly a ring of photos around a chimney, with one from above at -60°.
Stop for every photo
Hover about 2 seconds at each point and fly 1 to 3 m/s between them. Use a shutter of 1/500 s or faster. Overcast is ideal; with wind above about 6 m/s, move further out or come back another day.
Check the photos before you leave
Zoom in on a few at 100%. A soft photo costs a minute to redo on site and a whole trip once you are back at your desk.
What to look for on the photos
Go through the roof in the same order every time, so nothing gets skipped, and mark each finding on an overview photo.
- Covering: cracked, slipped or missing tiles and shingles, moss, and exposed underlay.
- Flashing: gaps and lifting around chimneys, skylights and valleys.
- Chimney: cracks, missing mortar and the state of the cap.
- Gutters and downpipes: blockages, sagging and loose brackets.
- Solar panels: broken glass, soiling and loose fixings. Add an angled pass to avoid glare.
Which drone for roof inspection?
For a house, you do not need an enterprise drone. A telephoto lens helps most, because it gives close detail from further away: useful near wires and trees. Of the drones Skyplanr plans for in DJI Fly (DJI Mini 4 Pro, DJI Mini 5 Pro, DJI Air 3, DJI Air 3S, DJI Mavic 3 Pro, DJI Mavic 4 Pro), choose by the lenses you need and what you already own.
Finding moisture or heat loss takes a thermal camera, which means an enterprise drone such as the Mavic 3 Thermal or Matrice 4T, and training in reading the images. Flown for pay, a roof inspection falls under Part 107 in the US and the EASA categories in Europe. Check the rules for flying over neighbours and people where you are.
Plan the roof inspection in Skyplanr
Tap the building and say what you need to check. Skyplanr plans the overview, grid and detail stops in order, runs 106 checks and sends the mission to DJI Fly (how the KMZ gets there). Close passes need measured heights: where laser data is missing, the plan stays higher and lists the close work as a manual flight.
See the technologyQuestions
How do you inspect a roof with a drone?
Take a few overview photos, fly a straight-down grid over the roof, shoot each pitched plane along the eaves at an angle, and make close stops at chimneys, skylights and flashing. Hover for each photo so it stays sharp.
What is the best drone for roof inspections?
For houses and small buildings, a camera drone with a telephoto lens is usually enough, since it gives close detail from further away. You only need a thermal enterprise drone if the job is finding moisture or heat loss.
How close should a drone fly to a roof?
Close enough for the detail you need: about 28 m for 1 cm/px with an Air 3S in the 12 MP mode. For finer detail, use the telephoto lens instead of moving closer to the roof, wires and trees.
Can a drone replace a roofer or a building inspector?
It replaces the climb, not the judgement. A drone shows the surface, and it can show where to look. Moisture in the structure, the attic and a signed condition report still need a person.
Sources
Skyplanr is not affiliated with the third-party guides linked here.
This guide describes how DJI Fly behaved when it was last checked; DJI can change the app at any time. It is advice, not a permission: you are the pilot in command, and the site, the geo-zones and the rules are yours to check before takeoff.
Let Skyplanr write the file.
Describe the job, and Skyplanr plans the waypoint mission, checks it and gives you the KMZ for DJI Fly.